If you find the OpenWrt device itself is only accessible from those computers directly connected to the W-LAN AP, not from the ones connected to the OpenWrt W-LAN client, when in the 192.168.1.0 subnet, Make sure the Local IPv4 address setting in the Relay bridge interface matches the ip address of the wireless uplink.
Oct 19, 2011 · How Does the Client Wireless Bridge Differ from Repeater Mode? To put it simply, a Client Bridge links computers while a Wireless Repeater connects routers. These mode changing options can be found in later builds of DD-WRT under the Wireless –> Basic Settings Tab (as seen in the image above). The default mode in DD-WRT is AP, which sets your Repeater / Repeater Bridge - Extend the Wireless access area using a second router WIRELESSLY connected to the primary. The secondary router must have dd-wrt installed; the primary does not need dd-wrt. Repeater Bridge - A wireless repeater with DHCP & NAT disabled, clients on same subnet as host AP (primary router). That is, all computers can May 26, 2019 · In essence, you will use the wireless repeater mode to broadcast the signal too weak to wireless clients - of course, assuming that the DD-WRT router can still receive the host AP. . During the test, we successfully repeated a host AP with a signal strength of only 9% using the DD-WRT router - so low that the laptop cannot detect the host AP. Apr 19, 2015 · This is part of a series: dd-wrt Repeater Bridge Thus far, you have successfully: Prepared to flash your router with dd-wrt Flashed your router with dd-wrt (The "trailed/killer" version, then the "real" one) Now it's time to tell your router to connect to another router over Wi-Fi, and act as if the 2 routers are… By default, DD-WRT is configured as an open / unsecured AP with the wireless name 'dd-wrt'. If you want to use the router as a repeater bridge, you will need to change a few settings. This is a relatively straightforward process, which will be shown in this tutorial. If you're upgrading to a faster, stronger wireless router, don't chuck your older Wi-Fi box. With the magic of DD-WRT, you can turn your older wireless router into a range-expanding Wi-Fi repeater
I configured DD-WRT as a repeater bridge and I’m able to use my wired ports, but the wireless broadcast is not working. My primary router is set to channel 11 and I’ve set my repeater bridge to the same channel. I’ve noticed the repeater bridge broadcasts on channel 9 and stays on that channel even when I reset it. Is there a bug with DD-WRT?
I'm having one problem with Repeater Bridge using DD-WRT v24 RC-6 (12/30/07) std (SVN revision 8733M Eko)nokaid. I have one PC that connects to the AP router, but can't see any other devices
The AirStation should now be connected as a wireless extender. To configure the AirStation's SSID and security settings, click on the Wireless tab and then the 2.4 GHz (or 5 GHz) subtab. (Optional) To use the AirStation as a repeater instead, simply click the Repeater checkbox on the Wireless Bridge page.
May 26, 2019 · In essence, you will use the wireless repeater mode to broadcast the signal too weak to wireless clients - of course, assuming that the DD-WRT router can still receive the host AP. . During the test, we successfully repeated a host AP with a signal strength of only 9% using the DD-WRT router - so low that the laptop cannot detect the host AP. Apr 19, 2015 · This is part of a series: dd-wrt Repeater Bridge Thus far, you have successfully: Prepared to flash your router with dd-wrt Flashed your router with dd-wrt (The "trailed/killer" version, then the "real" one) Now it's time to tell your router to connect to another router over Wi-Fi, and act as if the 2 routers are… By default, DD-WRT is configured as an open / unsecured AP with the wireless name 'dd-wrt'. If you want to use the router as a repeater bridge, you will need to change a few settings. This is a relatively straightforward process, which will be shown in this tutorial.